Boiler Installation Exeter

Best Boiler Installation in Exeter

Get up to 3 Boiler Installation quotes for your project today! Compare profiles, reviews, accreditations, portfolio, etc... and choose the best offer.

Service Needed
City or Town
Find Pros

Over 15,611+ HVAC Businesses registered

Our HVAC companies operate in Exeter and surroundings!

HVACCompaniesHub has curated and vetted Top HVAC Contractors near Exeter. Find the most trustworthy pro today.

Frequently Asked Questions About Boiler Installation

Planning a new boiler installation? Find answers to common questions and make informed decisions for your heating upgrade.

What is a combi boiler?

A combi boiler (combination boiler) heats both your water and your home without a separate tank. They are much smaller than traditional boilers, saving valuable space. Combi boilers are very popular in flats and houses with less hot water requirements since they deliver hot water instantly to taps and showers. If you use a lot of hot water at once, the temperature and pressure may decrease; however, the hot water is readily and immediately replaced by more heated water.

How do I repressurize my boiler?

If the pressure gauge on your boiler shows low pressure, you'll need to repressurize the system. Repressurizing is a straightforward process:1. Turn off your boiler and allow it to cool.2. Locate the filling loop. This is usually a flexible braided hose connected to your mains water supply and boiler, under the unit. It may have a valve or tap.3. Open both valves on the filling loop carefully, usually counterclockwise. . You should hear water flowing into the system. .4. Keep an eye on the pressure gauge. When the pressure reaches the recommended level (usually between 1 and 1.5 bar), close both valves on the filling loop turning clockwise.5. Turn your boiler back on. Confirm that pressure is at an appropriate level. If problems persist, contact a qualified HVAC technician.If you're uncomfortable performing this task yourself, contact a Gas Safe registered engineer. Ensure your safety and avoid costly repairs by having it done right.

What is a power flush, and do I need one for my new boiler?

A power flush is a deep cleaning of your central heating system, using specialized equipment to remove sludge, rust, and other debris that can build up over time. This buildup can restrict water flow, reduce heating efficiency, and cause damage to your boiler and other components.While not always strictly necessary with a new boiler, a power flush is often recommended, especially if you're replacing an older system. It ensures that your new boiler is installed in a clean and efficient system, maximizing its performance and lifespan. A clean system also helps reduce noise and improve heat distribution.Signs that you might need a power flush include cold spots on radiators, slow heating, frequent boiler breakdowns, or noises coming from your heating system. Discuss with your boiler installer whether a power flush is advisable for your specific situation.

How do I turn off my boiler?

To turn off your boiler, locate the main switch or control panel. There will be an on/off switch or a mode selection dial. Switch the boiler to the 'off' position or turn the dial to the '0' or 'reset' setting. . For extra safety, you may also want to turn off the gas supply to the boiler, if applicable.

What is a combi boiler?

A combi boiler (combination boiler) provides both central heating and domestic hot water on demand, directly from the mains water supply. They are much smaller than traditional boilers, saving valuable space. Combi boilers are very popular in flats and houses with less hot water requirements since they deliver hot water instantly to taps and showers. If you use a lot of hot water at once, the temperature and pressure may decrease; however, the hot water is readily and immediately replaced by more heated water.

How do I repressurize my boiler?

If the pressure gauge on your boiler shows low pressure, you'll need to add water to the system. Repressurizing is a straightforward process:1. Turn off your boiler and allow it to cool.2. Locate the filling loop. This is usually a flexible braided hose connected to your mains water supply and boiler, under the unit. It may have a valve or tap.3. Open both valves on the filling loop slowly, usually counterclockwise. . You should hear water flowing into the system. .4. Keep an eye on the pressure gauge. When the pressure reaches the recommended level (usually between 1 and 1.5 bar), close both valves on the filling loop turning clockwise.5. Turn your boiler back on. If the pressure is still low, repeat the process..If you're uncomfortable performing this task yourself, contact a Gas Safe registered engineer. Ensure your safety and avoid costly repairs by having it done right.

What is a power flush, and do I need one for my new boiler?

A power flush is a deep cleaning of your central heating system, using specialized equipment to remove sludge, rust, and other debris that can build up over time. This buildup can restrict water flow, reduce heating efficiency, and cause damage to your boiler and other components.While not always strictly necessary with a new boiler, a power flush is often recommended, especially if you're replacing an older system. It ensures that your new boiler is installed in a clean and efficient system, maximizing its performance and lifespan. A clean system also helps reduce noise and improve heat distribution.Signs that you might need a power flush include cold spots on radiators, slow heating, frequent boiler breakdowns, or noises coming from your heating system. Discuss with your boiler installer whether a power flush is advisable for your specific situation.

How do I turn off my boiler?

To turn off your boiler, locate the main switch or control panel. There will be an on/off switch or a mode selection dial. Switch the boiler to the 'off' position or turn the dial to the '0' or 'reset' setting. . For extra safety, you may also want to turn off the gas supply to the boiler, if applicable.